CHARACTERISTICS

Operating speed	0.05mm to 50cm/s
Operating frequency	Mechanically:120 operations/min Electrically:30 operations/min
Contact resistance	15mΩ max.( initial)
Insulation resistance	100MΩ max.( at 500 VDC)
Dielectric strength	1,000VAC,50/60Hz, fo 1 minute between non-continuous terminals 1,500VAC,50/60Hz, for 1 1minute between current-carrying and non-current-carring pasts and between each terminal and ground
Vibration	Mechanical durability:10 to 55HZ, 1.5mm double amplitude
Shock	Mechanical durability:1,000m/S²(approx.100G's)malfunction: 500m/S²(approx.50G's)
Ambient temperature	Operating:-5 to +65ºC
Humidity	95% HR max.
Service life	Mechanically:10,000,000 operations min. (At rated ot value)Electrically:500,000 operations min
weight	Approx.130g to 190g
Degree of protection	IEC:IP65

SPECIFICATIONS

• RATINGS

NOTES : 1. inductive load has a power factor of 0.4 min. (Ac) and a time constant of 7 msec. Max.(dc)
2. lamp load has an inrush current of 10 times the steady-state current, while motor load has an inrush current of 6 times the steady-state current.

CONTACT CONFIGURATION

  

OPERATION CHARACTERISTICS

TYPE	TZ-1104	TZ-1108	TZ1107	TZ-1111	TZ-1112 TZ-1122	TZ-1166 TZ-1167 TZ-1168 TZ-1169
OF max.	750g	750g	750g	900g	900g	150g
RF min.	100g	100g	100g	150g	150g	-
PT max.	20º	20º	20º	1.5mm	1.5mm	30mm
OT min.	50º	50º	50º	4mm	4mm	-
MD max.	12º	12º	12º	1mm	1mm	-
OP	-	-	-	26±0.8mm	37±0.8mm	-

SPECIFICATIONS

• high precision and long life (10,000,000 mechanicaloperations)
• Sealed with gasket diaphragm to provide high sealing property without use of any adhesive or pin

Operating speed	0.01mm to 50cm/sec ( at pin plunger)
Operating frequency	120 operations/min
Contact resistance	15mΩ max.( initial)
Insulation resistance	100MΩ max.( at 500 VDC)
Dielectric strength	1,000VAC,50/60Hz, fo 1minute between non-continuous terminals 1,500VAC,50/60Hz, for 1 1minute between current-carrying and non-current-carring pasts and between each terminal and ground
Vibration	Mechanical durability:10 to 55HZ, 1.5mm double amplitude
Shock	Mechanical durability:1,000m/S²(approx.100G's)malfunction: 300m/S²(approx.30G's)
Ambient temperature	Operating:-10 to +80ºC
Humidity	95% HR max. ( at+20 to+35ºC)
Service life	Mechanically:10,000,000 operations min. (At rated ot value)Electrically:500,000 operations min
weight	Approx.60g
Degree of protection	IEC:IP65

SPECIFICATIONS

• RATINGS

OTES : 1.inductive load: powerfactor=0.4;

               time constant =7msec.

            2.Iamp load has an inrush current of 10 time the steady-state current while motor load has an inrush current of 6 times the steady-sate current.

CONTACT CONFIGURATION

   

OPERATION CHARACTERISTICS

 

• DIMENSIONS
• 
• 
• 

 

CHARACTERISTICS

Operating speed	1mm to 2mm/s (TZ5104)
Operating frequency	Mechanically:120 operations/min Electrically:30 operations/min
Contact resistance	15mΩ max.( initial)
Insulation resistance	100MΩ max.( at 500 VDC)
Dielectric strength	1,000VAC,50/60Hz, fo 1 minute between non-continuous terminals 2,00VAC,50/60Hz, for 1 1minute between current-carrying and non-current-carring pasts and between each terminal and ground
Vibration	Malfunction durability:10 to 55HZ, 1.5mm double amplitude
Shock	Mechanical durability: approx. 1,000m/S²(approx.100G's) Mechanical durability: approx. 300m/S²(approx.30G's)
Ambient temperature	Operating:-10 t~+80ºC
Humidity	95% HR max.
Service life	Mechanically:15,000,000 operations min. (At rated ot value)Electrically:500,000 operations min
weight	Approx.275g (with Type TZ-5104)
Degree of protection	IEC:IP67
Temperature rise	50 degrees max.

SPECIFICATIONS

• RATINGS

OTES : 1. inductive load has a power factor of 0.4 time. constant =7 msec.

            2. lamp load has an inrush current of 10 times the steady-state current, while motor load has an inrush current of 6 times the steady-state current.

CONTACT CONFIGURATION

  

Note 1 : Adjustable roller arm (50 dia. rubber roller) type is IP65.

OVERTRAVEL TYPE

The Overtravel Type is a limit switch which is provided with a greater OT to facilitate dog setting. Since this type is identical to the Basic Type in dimensions, both types are interchangeable.The Overtravel Type is classified into two versions -2 series and -2N series. 

-2 SERIES

The head of - 2 series switch can be installed in any of the four directions.

90* operation on only one side - impossible

90* operation on either side - possible

- 2N SERIES

The head of -2N series switch can be installed only in two directions, forward and backward.

90* operation on only one side - possible

90* operation on either side – possible

 

OPERATION CHARACTERISTICS

TYPE	TZ-5101	TZ-5102	TZ-5109	TZ-5104	TZ-5108	TZ-5107	TZ-5105
OF max.	2,720g	2,720g	2,720g	1,360g	1,360g	142g	1,200g
RF min.	910g	910g	910g	227g	227g	28g	-
PT max.	1.7mm	1.7mm	1.7mm	20º	20º	20º	55º
OT min.	6.4mm	5.6mm	5.6mm	30º	30º	30º	35º
MD max.	1mm	1mm	1mm	12º	12º	12º	-
OP	34±0.8mm	44.8±0.8mm	44.8±0.8mm	-	-	-	90±10º
TTP max.	29.5mm	39.5mm	41mm	-	-	-	-

 

TYPE	TZ-5106.5166.5168.5169	TZ-5104-2.5108-2	TZ5104-2	TZ-5104-2N.5108-2N	TZ-5107-2N
OF max.	150g	1000g	290g	980g	290g
RF min.	-	100g	25g	120g	250g
PT max.	28mm	20º	20º	20º	20º
OT min.	-	55º	55º	70º	70º
MD max	-	12º	12º	10º	10º

• Mounting holes

  Basic type and-2 SERIES

   

• DIMENSIONS

• 
• 
• 

คุณสมบัติ

Load		Resistive load (COSϕ = 1)	Inductive load (COSϕ = 0.1)
AC	125V	6A	6A
	250V	6A	6A
	380V	6A	3A
DC	24V	5A	2.5A
	60V	1.5A	1.5A
	220V	0.3A	0.3A

Note : When DC voltage is applied, the time constant is (T=) 0ms for resistive load, (T=) 100ms or less for inductive load.

Characteristics
Contact arrangement		1 Form A 1 Form B
Initial contact resistance, max.		25mΩ (By voltage drop of 5 to 5 VDC 1A)
Contact material		AgCdO
Initial insulation resistance (At 500VDC)		Min. 100MΩ
Initial breakdown voltage		1,000Vrms for 1 min Between non-consecutive terminals 2,500Vrms for 1 min Between dead metal parts and each terminal 2,500Vrms for 1 min Between ground and each terminal
Shock resistance	Functional	Max 294 m/s2 (equivalent 30G) (note 1)
	Destuctive	Max 980 m/s2 (equivalent 100G)
Vibration resistance		10 to 55Hz, double amplitude of 1.5mm
Expected life (min. operations)	Mechanical	107 (at 120 cpm)
	Electrical	1.5 x 105 (at 20 cpm, 6A 380VAC resistive load)
Ambient temperature		-30 to 80°C (-22 to 176°F) (but not in a frozen environment)
Ambient humidity		Max 95%RH (without dew at 40°C (104°F))
Max operating speed		120 cpm

Note : The rating, chaeacteristics and operating characteristics are based are on the bassic mpdel.
Note 1 : This value applies when the arm length of the adjustable roller arm (50 dia. rubber roller) is 70 mm or less

EN60947-5-1 performance

Item	Rating
Rated insulation voltage (Ui)	250VAC
Rated impulse withstand voltage (Uimp)	2.5kV
Switching overvoltage	2.5kV
Rated enclosed thermal current (Ithe)	6A
Conditional short-circuit current	100A
Short-circuit protection device	10A Fuse
Protective construction	IP67 (Note 1)
Pollution degree	2

Note 1 : Adjustable roller arm (50 dia. rubber roller) type is IP65.

Operating characteristics

Characteristics	O.F. (N{gf}) max	R.F. (N{gf})min	Pretravel(PT) max mm inch	Movement diferential (MD) max mm inch	Overtravel (OT) min mm inch	Operating Position (OP) mm inch
Push plunger	6.37 {650}	1.47{150}	2 .079	1.2 .047	4 .157	18±0.5 .708±020
Roller plunger	6.37 {650}	1.47{150}	2 .079	1.2 .047	4 .157	28±1 1.102±03
Roller arm	4.90{500}	0.49{50}	20° to 26°	14°	30°	-
Roller level	3.92{400}	0.78{80}	4 .157	1.6 .063	5 .197	-
Adjustable roller arm (Note)	4.90{500}	0.49{50}	20° to 26°	14°	30°	-
Adjustable roller arm (50 dia. rubber roller)	4.17 {425}	0.42 {43}	20° to 26°	14°	30°	-
Adjustable rod (2.6 dia)	4.90{500}	0.49(50)	20° to 26°	14°	30°	-
Roller level (vartical action)	4.41 {450}	0.88{90}	4 .157	1.7 .067	5 .197	27±0.8 1.063±031

Note
- The above values of adjustable roller arm shows the values when roller length is set at 26mm same as roller type.
- The value of adjustable roller arm (50 dia. rubber roller) type shows the value when roller length is set at 32 mm.
- The value of adjustable rod (2.6 dia.) type shows the value when length of rod is set at 26 mm same as the roller arm type.

Protective characteristics

Protective construction	DL mini limit switches
IEC
IP60	○
IP64	○
IP67	○(Note 1)

Note 1 : The value for protective function characteristics is the initially set value. Also adjustable roller arm (50 dia. rubber roller) type is IP65
The switches are compatible with DIN EN50047.